Troubleshooting guide; Service and repair of butane Gas Boiler

Wall gas boiler is one of the best and most popular heating appliances in the house, which in addition to providing hot water, also provides hot water needed for the boiler and heating appliances. With the onset of the cold season, wall gas boilers are used again, but it is better to do the wall gas boiler service first before the cold days begin, and if necessary, make the necessary repairs for it.


The wall gas boiler provides the domestic hot water for bathing and washing, as well as the hot water needed for the radiator, and with its use, there is no more noise and noise in the engine room. The gas boiler is actually a small engine room that is installed separately for each residential unit and has become very popular due to its high efficiency and less space.


Wall gas boilers have many advantages over the boiler and engine room system and water heaters, the most important of which are easy and fast access to hot water, wall gas boiler of each unit of the whole building, adjusting the temperature of water and radiators to the desired size, occupation He noted less space in the house, reduced maintenance costs, optimal fuel consumption and high efficiency. Timely service of the wall gas boiler is the best way to maintain this widely used device, which greatly reduces the possible damages and side costs of servicing and repairing this device.


It is better to do the wall gas boiler service once every few months so that if there is a problem in any of the parts of the device, the necessary measures and repairs can be done as soon as possible, but in general, you must do the gas boiler service before the cold season. We recommend that you entrust the annual service of your wall gas boiler to a professional and professional repairman so that both the service and the descaling of the wall gas boiler are done well. If you have just bought or repaired a wall gas boiler, it is best to service it once every six months. If there are salts in the water and sediment in the parts and pipes of the radiator, certain signs appear in the system, in which case descaling should be done as soon as possible.


In order to be able to identify and fix the gas boiler problem, before any action, you must know the gas boiler manufacturer brand and gas boiler model. Because troubleshooting different gas boilers is a little different.

The cost of Gas Boiler repair and gas boiler service for repairing different types of gas boilers are different. For example, the cost of Iran Radiator gas boiler service and Iran Radiator gas boiler repair is different from the price of butane gas boiler service or Airfo gas boiler repair. In general, this cost difference is due to the way different parts work and cost in different brands. For example, the method of draining the water of butane gas boiler is different from the method of draining the water of Iran radiator gas boiler. In addition, the method of draining the gas boiler water is different in other brands.


Butane gas boiler repair

In order to troubleshoot butane gas boiler repair and solve its problems, you need to have enough information about the error codes of this gas boiler. Below we review the butane gas boiler errors in different models.

Error code of butane gas boiler model 324

Red one tenth of a second (flashing red flashes once every tenth of a second six times per second) NTC piece

Red five tenths of a second (flashing in a row) Consumption potentiometer piece between 80 and 70 heating

Fixed red (flashes once every second) Fault, malfunction or failure of double thermal switch or thermostat, no flame formation, sensor ignition gas valve,

✔ Red every second (flashes twice every second) Torch does not light up between two or three ignition cycles

✔ Red every one second (beats twice every second) Defective water pressure switch or two-amp fuse


Error code of Alta type butane gas boiler

Fixed yellow: Consumption, NTC consumption is disconnected

Flashing yellow: The status of the maximum power of the amount consumed is the power of the device

Fixed red: NTC smoke thermostat heating, no flame formation, control board defective, minimum water pressure switch

Flashing red: The heat switch is on

Fixed green light: The torch is on

Flashing green light for one to five seconds: The system is in standby mode five times per second. No application has been issued.

Quick flashing green light: Limited input and output, check input and output.

Blinking green light every five tenths of a second: winter mode, standby mode, smoke pressure, pump set fan set, minimum water pressure switch fault for up to ten minutes, NTC false resistance lock, condenser switch fault


Optima model butane gas boiler error codes

If your device shows one of the items mentioned below, be sure to contact a DJI dealer at the earliest opportunity.

Fixed yellow: Consumption, NTC disconnected

Blinking yellow: Maximum power status, the amount of power consumed is more than the power of the device.

Fixed red: NTC smoke thermostat heating, no flame formation, control board, minimum water pressure switch fault

Flashing red: The thermal switch is operated

Fixed green light: Torch lit.

Flashing green light five times per second:: The system is in standby mode five times per second. No application has been issued.

Fast flashing green light: Limited input and output, check input and output.

Flashing green light every five tenths of a second: winter mode, standby mode, smoke pressure, pump set fan set, minimum water pressure switch faults for up to ten minutes, NTC false resistance lock, condensed pressure switch faults

Related image
Benzene Pro Butane gas boiler gas boiler Error Code

56, 57, 58, 59, 60, EL21, EL22, EL30, EL31, EL50, 20, 21, 22, 30, 31, 40, 41, 42, 50, 51, 52, 53, 54, 55, 10, 11


Roma model butane gas boiler repair

If your gas boiler shows such error codes or errors, it means that the device needs to be repaired. The error codes include: flashing summer winter lights, A01, A02, A03, A04, A06, A07, A11, ADG


Error code of butane gas boiler model CV

E1, E13, E15, E17, E2, E25, E27, E29, E3, E4, E5, E6, E7, E8, E9, E99


Error code of Negan Benzel model butane gas boiler

1, 2, 3, 4, 5, 6, 7, 8, yellow flashing, red flashing


Error code of butane gas boiler model Verna 888

E01, E02, E03, Permanent lock E04, Temporary lock, E06, E07, E09, E11, E12, E26, E37, E40, E41, E42, E43, E44, E62, E72, E80, E81, E82, E83, E84 , E98, E99


Error code of butane gas boiler model Perla device

ADG, E01, E02, E03, E04, E06, E07, E011, flashing lights and temperature


Calda model butane gas boiler error code

Fixed red: Function or breakdown of the thermal switch or breakdown of the smoke thermostat

Flashing red: Definitive in NTC

✔ Red Yellow, Yellow Simultaneous: Minimum water pressure switch fault



Calda venezia butane gas boiler repair

Flashing yellow: Suped or maximum power status

Fixed yellow: The NTC sensor is disconnected

Flashing green one to five seconds: standby, no demand for use

ثابت Fixed green: lighted torch

✔ Blinking green every five tenths of a second: winter mode, standby mode, smoke suppressor, pump pump stopper

✔ Quick flashing green: Check control system

Fixed red: NTC sensor, smoke thermostat heating, no flame formation control board

✔ Blinking red



In general, we have two types of defects in the wall-mounted boiler system:

1- The first defects that are identified by the electronic board and will be notified to you by the error code. Of course, this error code in the analog gas boiler is determined by the blinking of one or more lights, and in digital gas boilers, this error code appears on the monitor.

To repair the gas boiler and troubleshoot such defects, first of all, you should refer to the error code page of wall-mounted radiators, which is also available in the site menu, and use the error codes announced on this page to describe the troubleshooting you see. There is a defect.

2- Troubleshooting defects that do not report any errors but disrupt the operation of the gas boiler. In the following, with some examples, we will examine some of these defects that disrupt the operation of the gas boiler but the electronic board is not able to detect them.

Radiators do not have adequate heat:

Before any action, make sure that the radiators are ventilated and the gas boiler load pressure is adjusted.

Source: https://dgsos.ir